 |
|
 |
 |
|
"For over 50 Years we have been a full service Heating and Air Conditioning company committed to providing our customers with quality products backed by expert technical service and friendly, responsive customer service. We offer design, installation, repair, and emergency services in both residential and commercial settings. We build our business one customer at a time with face to face interactions that establish personal relationships to encourage loyalty and repeat business.
We work diligently to maintain and build our reputation for providing quality equipment installed and serviced by qualified, professional, and well-trained mechanics. We take pride in the comfort of our customers in their home or workplace and strive to always provide the highest quality products and service at a reasonable price, thus ensuring maximum value for each consumer dollar." - William C Potts, President
This website has been designed to be informative, direct, and convenient. To show our customer appreciation
Our top-quality mechanics are skilled in the many fields of Heating & Air and that enables us to offer quality service. Not only do you get quality service, but you get the peace of mind that all of our skilled workers are under our insurance and Worker's Compensation.
Safety is our top concern, and so is being professional.
Thank you for stopping by, and we always appreciate your business! | |
 |
 |
 |
 |
|
What do WE do on a tune-up?
Our qualified service technicians go through an extensive checklist. Here's a glimpse of what we do:
FURNACE 26 Point Task List:
1. Inspect proper thermostat operation
2. Heat anticipator check
3. Air filter and size inspection
4. Check blower motor operation
5. Lubricate blower motor if applicable
6. Blower belt check if applicable
7. Inspect blower wheel
8. Clean burners and burner compartment
9. Video the heat exchanger with camera
10. Check electrical connections
11. Inspect low voltage wiring
12. Test safety controls operation
13. Inspect all drain lines in high efficiency units
14. Clean pilot assembly and orifice
15. Check and adjust gas pressure
16. Cycle gas valve check performance
17. Use OHM meter to test the hot surface ignitor
18. Check blower motor capacitor
19. Adjust combustion air if needed
20. Record, clean & inspect flame proving sensor
21. Record and inspect temperature rise
22. Inspect flue and draft
23. Use detector to check gas lines for leaks
24. Inspect the ductwork
25. Record and perform CO test
26. Clean the exterior of the unit
BOILER 22 Point Task List:
1. Inspect proper thermostat operation
2. Heat anticipator check
3. Check pump motor operation
4. Lubricate pump motor if applicable
5. Drain expansion tank if applicable
6. Check pigtail if applicable
7. Clean burners and burner compartment
8. Check electrical connections
9. Inspect low voltage wiring
10. Test safety controls operation
11. Inspect all drain lines in high efficiency units
12. Clean pilot assembly and orifice
13. Check and adjust gas pressure
14. Cycle gas valve check performance
15. Use OHM meter to test the hot surface ignitor
16. Adjust combustion air if needed
17. Record, clean & inspect flame proving sensor
18. Inspect flue and draft
19. Use detector to check gas lines for leaks
20. Inspect the piping & automatic controls
21. Record and perform CO test
22. Clean the exterior of the unit
HEAT PUMP & CENTRAL A/C 20 Point Task List
1. Calibrate and level thermostat
2. Clean filters as needed
3. Monitor volts/amps on fan motor
4. Lubricate and inspect bearing for wear
5. Inspect indoor coil if accessible
6. Inspect condensate drain
7. Inspect condenser coil
8. Monitor operating pressures of refrigerant
9. Inspect safety devices for proper operation
10. Inspect disconnect box for proper rating and installation
11. Tighten all electrical connections
12. Test/inspect contactors for burned, pitted contacts
13. Inspect electrical for exposed wiring
14. Test and inspect capacitors
15. Inspect fan blade
16. Clean condenser coil/remove debris
17. Inspect service valves for proper operation
18. Measure temperature difference-supply return
19. Inspect duct work for energy loss
20. Monitor compressor for proper amperage, volt draw and wiring connections
HUMIDIFIER: Check Wiring - Check Water Supply - Check Drain Line - Check Damper & Humidistat - Check Water Panel / Replace if necessary
ELECTRONIC AIR CLEANER: Check Wiring - Check Voltage - Check Pre-Filter & Cells / Clean if necessary
|
